Now the entire console bezel will pull forward. Castrol makes an import fluid but I have heard several places that it is not compatible. For example, it could be the oxygen sensor. Pop out cup holder in console. This transmission unit has been inspected, tested and ready to ship. I had no more gears couldn't drive.
Sometimes, even if you've done everything the right way, you can destroy, or damage, a piece, or part. Do not mix with other fluids. Please let me know what you think If you have a check light on then of course that would be your best bet to go to Autozone or elsewhere and have them pull the codes for you to try and give you a clear understanding. There is a big support chassis with a reinforced area that you can put the jack under. I've lifted the car up and had a good look under it and for the life of me I cannot work out where the filler plug is.
I removed the filter and repl … aced it. If the resistance is within specification go to Step 5. Now look under drivers side dash just above gas pedal. The glove box will now fold down out of the way. I found that just going to step 2 was enough to remove my stereo, so check this first.
The fill plug is a big nut. It is indeed a manual transmission. Also, if for some reason, I do give incorrect instructions, and something breaks because you followed my instructions, I still will not reimburse, or pay, in any way, for whatever cost that may be incurred due to following my wrong instructions. As a matter of interest I did manage to change the oil and for those who are are interested I attach some instructions below that are a bit more useful than those in the manual Undo the filler the cap and loosen the dip stick The oil filter is located at the front left side of the engine on the front of the sump and is hidden under a hose outlet. This happened when he started his car tonight real cold night -23 Celc.
Any help would be greately appreciated. Mixing isn't recommended either - as you will affect the slip-coefficent of the final product. But lately they have had a few vehicles with the same problem I think this should be a recall. Turns out the shifter rod goes into the transmission and is held in place with a shear pin. Reconnect the pulse generator connectors and reattach the connector to the bracket. The car just slams or jerks into gear. In line with the oil filter but at the back of the sump there is the drain bolt for the sump.
Posted on Dec 11, 2008 First, check to make sure your fluid level is correct. They won't keep the car long enough to fix it. This went on until they stated they put in a new transmission. If you stick a pencil in the slot you should be able to release the car from park. The drain plug is at the right side of the trans, at bottom right. Also, the bezel refers to the smooth part of the dashboard with the hazard light button, heater controls, air vents, clock, etc.
Change it, scrap the sealant, change also the gasket. Then I removed the magnets from the pan and checked and removed all particles. Is this electical or mechanical related … ; perhaps a fuse is blown although which one? There's a diagram in the owners manual but its incomprehensible. If it can't read the exhaust correctly, then it gives bad info to the engine's computer chip and screws everything up. It is usually Diamond brand.
I had to do this for about two weeks and then it fixed itself. There are 6 choices for the 2001 Hyundai Accent Transmission Assembly!!! Then remove the trans pan, then you'll see the filter inside the trans. In this video I show you how to check your manual transmission fluid in your 01-06 Hyundai Elantra. Next remove glove box by popping out the 2 black clips on each side of the glove box. This transmission unit includes a transmission case, valve body, tail shaft and housing, torque converter automatic only , and all internal lubricated parts. All manufacturers logos,and marques,all other trademarks are the property of their respective owners. Then fill the oil in the trans.
Simply loosen and unscrew the fan clutch from the water pump shaft. Remove all the bolts, trans oil will start leaking out of the gasket. After that I dropped the pan by unscrewing all the nuts on the pan. ProTools, perhaps among others, makes an inexpensive set of wrenches out of heavy stamped steel. When I arrived at the dealership, they had it up front waiting on me.